Here are Todays Amazing Kit Tooling Deals
More Great Information on Kit Tooling:
Getting Parts For A Motorcycle by Victor Epand
Tune-ups don't require ignition coil replacements. Sometimes you need to replace the spark plug caps on the ends of the wires, though. The resistance value should be around 5K ohms. Honda Tune up kits generally has plugs, points and condensers in them, as a set. The number of miles you have on the bike engine and the overall care it has had makes a lot of difference in what you will need and what may keep going for you, for a while.
The tools that came in your kit, if complete, could barely get you by on repairs/tune-ups. If you own a bike, you need to know about how to repair it and have the tools to do the job. You can go to Wal-Mart, Costco and elsewhere and get giant tool packages for $100 or less that will get you going pretty well. An Impact Driver with a selection of bits and a good hammer will be a good investment! Steel screws, resting in aluminum threads for such a long time will setup corrosion in the threads that can spell trouble in some cases.
The cables are now 33 years old.... probably time for a change! If your bike is a 1973 CB350G, then it has a front disk brake that has its own maintenance issues. Same with the CB350F. The "regular" CB350 twins had cable operated drum brakes.
You can get a lot of stuff on EBay, as far as tune-up parts go. You need to identify the exact model, of course, before you move forward, plus a good tune-up guide and/or shop manual will be useful. I have a PDF version of a minor tune-up guide that is a reprint from a Cycle Guide magazine special booklet, but it only covers CB350 Twins. The principles of engine tuning are all the same, but the details between 2 and 4 cylinder bikes are somewhat different in layout of components.
If you used stabil or some kind of gasoline stabilizer for the winter, the carbs should be okay. I would certainly drain them and refill the tank with fresh gasoline. Yamaha makes a carb cleaner that you mix with gasoline and then funnel down the carb fuel line to clean out the parts in the float bowl while it is together. Depends on what kind of condition the parts are in, though. Honda carbs have numerous O-rings inside that need replacing after 33 years!
What you could do, and it may require some modification on your part, is to find a hard bag mount set for your bike and then go to a motorcycle salvage yard and see what they have that you may like. You would likely have to repaint them, but that requires a wind-free place to work and a bit of light sanding and paint and a few hours.
Alternatively, if you know how to work with fiberglass, you could build the bags you want yourself, but this is a long-term project that will eat up a lot of your spare time to do it quickly. You can also look on a few of the catalogue sites. In addition to that, try some of the e-groups for Kawasaki and Vulcan's. There are a lot of specialized e-groups out there for specific makes and models of bikes. Look there, as there may be someone who is getting rid of a set that will work on your bike. It will certainly be less expensive than new.
Honda pretty much washes their hands of responsibility of supplying parts after about 10 years after end of production. They have made thousands of different models and dozens of variations of many of those, so the parts inventory and production considerations are staggering in any case.
Honda does have a vintage parts division, apparently in Japan who will make small quantities of some items that they still have tooling for, like exhaust systems for some of the fours. CB750 primarily. CMS in Holland is tied to them, to a certain extent and almost had them remake the missing #2 pipe for the 350Fs but the cost got too high.
Companies like apex cycle, retrobikes and a few others are having Asian companies remake some items. You won't be seeing any new crankshafts or engine cases coming from Honda or anyone else. Tooling and production of this stuff is way too expensive nowadays.
I have a source in Australia who makes new Dream and CB77 mufflers from stainless steel.
It is a small company and he's willing to do the tooling in-house just to produce the parts, but he's getting near retiring and that source will dry up one day. A company in NZ made some beautiful new CB77 mufflers a few years back, but the supply is now gone, I believe and they don't seem interested in doing another run again.
If there is sufficient demand, someone usually steps up and takes a shot at having parts made, but there are so many parts in a bike and so many models, that it is impossible to expect that the supply line for 40+ year old motorcycles is going to continue indefinitely. Brit bikes and scooters remained relatively unchanged for many years, so making parts for those is less of a stretch, than doing Honda camshafts for 250-305s... there were three versions of splines on just those parts.
Victor Epand is an expert consultant at http://www.SellUsedMotorcycleParts.com/. Sell Used Motorcycle Parts is a community of various independent used motorcycle parts sellers from around the world. Each used motorcycle parts seller represents a unique style of products all their own.
Article Source: http://www.earticlesonline.com/Article/Getting-Parts-For-A-Motorcycle/193220
how to install microsoft 2003?
im trying to install it righ now.. but i dont know what to choose from these choices!
Install Microsoft Office 2003
Install Microsoft Office Professional Edition 2003 <--- When i click this it always goes error
Install Microsoft Office FrontPage 2003
Install Microsoft Office Visio 2003 Professional
Install Microsoft Office Project 2003 Professional
Install Microsoft Office OneNote 2003
Install Microsoft Office 2003 Editions Resource Kit Toolbox
Install Microsoft Office Visio 2003 Resource Kit Tools
Install Microsoft Office 2003 is not part of the Choices 
What's the error message?
